maybe power throttle.

use gloves man

"Standard" aka Freedom units

just use pliers to hold the screw while tightening with a wrench :)

It's like watching a mad scientist.

Jay cut the handle off of the c clamp and weld a nut on then use a dial type torque wrench

Oh yeah my heart goes out to you cause you broke your RTX3090 and yet have a spare and then some. Yet here I am with a RTX1050 and can't get anything better at the moment and can't run half the games on the market. So sad

Any loose thread can be held by lock tight. There are different grades and stud holding. Depending on whether permanent is acceptable.

I enjoy seeing the struggle....It makes it 'real' ......

In Modern Living Rooms Everyone Using "SoundProof Curtains" That Stops Outside Noise by 80% (25 Db) Tested. Check Here: livesoundproof.com/best-soundproof-curtains/

Or you could tap it

They do have them...... ace

Why would anyone do this to a 2000 dollar GPU...whats the point?

Jay, a youtuber in America: accidentally whacked a resistor off the board while lapping the die - sends the card to manufacturer Me, a normie in Russia: opens the card to clean it from dust and change the old paste - warranty void due to bloody sticker

Send it to Taiwan ... ?? Dude, I see palm trees in the background, that means Florida or Cali. If Florida, than sorry can't help you. But if Calli ... nolocal.info My Bro Alex will fix you up in notime !!! xD cheers from Poland

Maybe u can try to bolt those nuts with a torque screwdriver. They have a much lower range of torque.

Loctite

I would have sent it to Louis FIRST.....then EVGA. Keep doing these videos. We all get frustrated at times and you are just a normal person too. We are here for the ride......bumps and all.

2:10 they make micro torque wrenches.

is this the card you did not send to louis to fix? the one you "fixed yourself"? XD

Don't pretend like your fingernails are dirty when they are not.

Still looking for excuses..

Does anyone know where you can buy a GPU.

Oni Vamp

Måned siden

Ebay

If it is just the cap knocked off but solder pads are still intact should be very easy to fix with hot air gun. I guess you would have done it yourself in that case. Even if the pad is ripped off, as a workaround you can scrape some soldermask off the trace using a scalpel, solder a tiny slice of copper/aluminium strip to the track so that it extends long enough for a cap to land and make a good contact for both ends, solder it back with hot air gun and glue it in place to secure. Kinda of a micro surgery but anyone who has some experience with SMT PCB repair should be able to do it.

I was thinking you might break the 2nd card too.

problems in pararise jay? this is a mock up, you cant buy a rx 5600 for $380

this video is stressful

You guys still use inches and pounds? Grow and get with the 80's

You need a little Helicoil repaid kit

not the cheapest option but here is convenience and peace of mind there other options

www.amazon.ca/dp/B0788HH5KN/ref=redir_mobile_desktop?_encoding=UTF8&aaxitk=mJg66FOsxX9V-KIfLUep5Q&hsa_cr_id=2506687260101&pd_rd_plhdr=t&pd_rd_r=b80c4658-115d-441b-95cf-f42461ae3d90&pd_rd_w=ykzAm&pd_rd_wg=EDys5&ref_=sbx_be_s_sparkle_mcd_asin_0_title

get a torque wrench for putting rifle scopes on that would probably work

What about the special little torque driver that came with Threadripper chips? They "break" like a torque wrench don't they?

Ah... the cost of pushing boundaries.

I worked in a physics lab for 5 years. There's a reason we wear safety goggles, gloves and a lab coat while using liquid nitrogen. One splash in your eyes will permanently blind you - or, at best, cost a huge amount of time and energy and cash in hospital visits. At the very least wear lab goggles. Please.

Jay, I know you've already sent your card away, but there are many specialist electronic places with the capability to fix that board. Try STS Telecom (nolocal.info/post/39yMXOL0ubFxLWwF1RwelA.html). Just send it over and he'll solder that back in a jiffy !

Hindsight seeing that EVGA guy unable to wear a mask properly while standing next to Jay who was likely covid positive at the time

Wow...Jay....you are such a noob...you are old AF and can't solder....SMH

I wish I just had some stuff laying about and some nitrogen to play with, it's remotely possible I could be dangerous XD

Jay gave EVGA covid

you have to screw in the screws diogonally for even pressure otherwise one side will get more pressure

Olha o techlabs AEE!!!

international standard netwons per meter, for your application 4 inch pounds max 6

it looks ilks a ceramic capacitor because of the color. resistors are almost always black. color coded parts make a techs job easier.

Get it to Louis Rossmann I’m pretty sure he’d be able to fix it....

I love turning wrenches. My hands get stain from certain grease. usually if my hands and arms aren't covered in cuts, burns and my nails are clean. Just means it's been slow lol

I was like "Is that the pad still attached to the capacitor?"

Jason Lowmaster

Måned siden

Yeah, I thought it looked like the pad ripped off the board, too. That's never a good time.

Send it to Louis Rossman ahahaha

If that's one of those inexpensive 1/4" torque wrenches.. I stopped using mine on cars because it's too unreliable. NEVER MIND a GPU!

Team AMD!

No respect for ESD... tsk tsk

Hey, Jay, how tight do you want your clamp to be ? I think about 40-ish ...FPS is ok... 🐙🤷😆

for that size of screws you need only a couple in-lbs, that wrench is still oversized. what you need is a torque screwdriver like this one www.mcmaster.com/5871A51

I come from the future Jay you have covid

Jay have you considered using a Torque screwdriver for those small screws and delicate parts? keep all the great content coming.

"Tech Unplugged" Could be a good series title for these type of Vlog like videos.

"Europe units" more like rest of the world except for a few countries units haha edit.: guess i'm one of many that got triggered by that

Not much of an in house repair centre to be honest if they can't fix that.

yes you do need a break from these test Jayson yes and take that break from it😉😉😊😊👍👍😴😴🥱🥱

Gray Kitty of Gamers Nexus says that: "...technically a technician can do it with the proper equipment, but it looks like you broke the pad and part of the circuit board tracing off..." He guesses that: "...the side of that resistor with the dark 'end' has the pad still attached. Many issues with trying to 'repair' that kind of equipment." If you're lucky they'll replace it with the exact same board, or at worst they'll mount the GPU onto a 'new board.'

You can get torque handle screwdrivers with a 1/4” drive that go below 1Nm. One of those paired with a deep socket would be perfect for this application.

@JayzTwoCents It just breaks my heart. I would be happy to be able to get even 1080 ti, and you keep playing with these unobtainable GPUs... I'm so sad.

EVGA is WORTHLESS if they cant solder that back on there. wtf

Cant you mix somekind of wrench from threadripper original torque wrench?

Use heli coil for the strip thread. That's what people use to repair strip thread.

Can't find small metric screws at the hardware store? Go to a r/c hobby shop, be willing to bet you would fine what you need there.

there is torque charts on the web available for every screw sizes. Get a threads gauge to identify the right nut... any shop selling bolts and nuts can provide you the right one with this info. This stiffener plate with the loose screw... i would drill and install an helicoid to fix it. Helicoid insert in aluminum is strong as steel

"European units". 🤣 You mean the rest of the world units. Although, we do still have both in my country and it's easy to get tools or parts for either. Also, that soldering job would be done in house here and not sent to Taiwan or anywhere else. Techs here normally do it themselves rather than take it back.

J. A. G.

Måned siden

Considering the amount of junk that comes from asia with US system parts and the amount of things that come from Europe that comes with US system...I'm beginning to think that no one uses it aside from here

Keep doing these videos. I got frustrated and want to give up, then I saw you frustrated and I know it’s not me. I’m a grab a beer and keep going, I hope you get some good scores coming up!

How did he brake it off? Thought those things were on there pretty hard?

why dont you send this card to rossmann? way quicker than shipping it out of country

I also hate how precision doesn't retain settings but sadly afterburner doesn't seem to apply custom fan setting to all three fans on my card so anytime I shut my computer down or put it to sleep I have to re apply all settings.

I just love to se how hard and how much work it is too even get close to the top of the litt. Keep it up jay you can make it, i bilen in you.

Nice GLE 63 S tho

They named it King Pin so that criminals would buy it Jay.

All this for frame rates. Like, i get it but a bit much for the few extra frames lol

3:56 "standard vs. metric" A typical US view on things?!? Just to put this in the rigth place, in most of the countries of the world, metric is standard.

BigBadCiviC

Måned siden

it's typical for Americans to think the world revolves about them only

Jay sell me a kingpin 3090 lol I cant get ahold of one. Waiting since they released but no notify from evga....

"Let's go to EVGA" Can they give me a 3070 at MSRP?

where is this because i need to fix my 2070

learn to solder.. that was a two minute fix

Why was it so hard for them to replace a ceramic capacitor? Any half decent repair group should be able to fix that in 5-10 minutes with a hot air station, tweezers, and flux.

someone needs to take you to FASTENAL its like mecca for fasteners

Techlab nao e foda manito jay2real

don't beat yourself up jay! you have awesome content for the average joe/jane! down to earth unlike ltt ( fellow canucks) but you keep it real and honest for regular folk. sharing your struggles with tech, points to the fact that you keep it real and don't try to hide the blemishes. much appreciated ! much love to you and your crew! keep up the great tech tip content !!!!!!

Sum nuts? Didn't know the guy

Okay, but who's Mercedes is that?

completely unrelated to the video but does anyone have an actual answer to why the starter pc from nzxt has a 1050 series card ( idk if it is a ti or not )? i thought it had a gtx 1660 s or ti at minimum

Also called 6/32's...we use them in electrical

Thanks for flaunting what no one can get right now

his was a god colab with Rossman that guy is needing content and u have the content for him, and content for you and didnt even try....

Dont beat yourself up team. Punching up with the XOC lads is pretty impressive.

newton meters, probably spelled it wrong

you dun fcked it up

wtf is an inchpound? do you mean newtonmeter?

lol "standard vs metric"... metric IS the standard, you american imperialist!

Love these videos!

I can always screw deep enough..lol

What you need is an in-0z torque wrench

Waiting for EVGA to come back and say: "Well.. Have you tried praying to the Omnissiah?"